Hydroponics knowledge base

Every question this site answers, with its short answer, in one place. Each answer is the opening of an existing guide; follow the link for the steps, limits and sources. Terms are defined in the glossary.

Start hydroponics

Hydroponics for beginners: start growing food at home

Start with a small Kratky jar or a compact deep-water-culture kit and grow lettuce or basil. These forgiving combinations teach water level, nutrient mixing and light placement without adding plumbing.

Common mistake: A large multi-channel kit creates more cleaning and more failure points before you know what healthy roots look like.

Read the full guide →

How hydroponics works: roots, water, air and nutrients

Hydroponics replaces soil with a managed root zone. Water carries dissolved mineral nutrients; roots also need oxygen, a suitable pH and enough light above the plant.

Common mistake: Do not treat the reservoir as a set-and-forget vase. Its concentration, temperature and cleanliness change.

Read the full guide →

Indoor hydroponics: a practical UK room-by-room guide

A bright, washable spot with ventilation is more useful than a fashionable cabinet. Kitchens suit herbs; utility rooms suit larger reservoirs; living rooms need quiet pumps and careful spill control.

Common mistake: A dark cupboard with a strong light can become hot and humid surprisingly quickly.

Read the full guide →

Hydroponics with children: a safe food-growing project

A clear-sided Kratky jar containing lettuce is the simplest demonstration because the roots are visible and there is no mains-powered pump. An adult should handle nutrients, pH adjusters and any electrical equipment.

Common mistake: Do not use unlabelled chemicals or let children adjust pH.

Read the full guide →

Hydroponic systems

The Kratky method: passive hydroponics without a pump

Kratky growing suspends a plant above a static nutrient reservoir. As the level falls, an air gap forms and part of the root mass takes oxygen from it.

Common mistake: Constantly filling the jar to the top can drown the air roots.

Read the full guide →

Deep water culture explained: simple aerated hydroponics

Deep water culture keeps roots in nutrient solution while an air pump and air stone add circulation and oxygen. It is simple, productive and dependent on continuous power.

Common mistake: A silent or blocked air pump can turn a healthy root zone into a problem quickly.

Read the full guide →

NFT hydroponics explained: channels, flow and failure points

Nutrient film technique runs a shallow, continuous film of solution through slightly sloping channels. It suits leafy crops with modest root systems and demands reliable flow.

Common mistake: Do not assume steeper or faster flow fixes uneven channels; it can make distribution worse.

Read the full guide →

Ebb and flow hydroponics: flood tables for home growers

Ebb and flow periodically floods a tray of pots, then drains back to a reservoir. It gives roots alternating access to solution and air and handles larger media-filled plants.

Common mistake: Never leave a newly assembled flood table running unattended before a full leak test.

Read the full guide →

Wick hydroponics: the simplest passive system

A wick draws nutrient solution into an absorbent growing medium. It has no pump and suits small herbs, but it cannot move enough water for thirsty, fruiting crops.

Common mistake: Adding more concentrated feed does not compensate for a wick that cannot supply enough water.

Read the full guide →

Dutch bucket hydroponics for tomatoes and cucumbers

Dutch buckets drip-feed individual media-filled pots and return the drainage to a reservoir. They suit large fruiting plants because each root zone has room and can be accessed separately.

Common mistake: Do not expect small clips or a light shelving unit to carry mature vines.

Read the full guide →

Aeroponics at home: benefits, complexity and backup plans

Aeroponics mists bare roots in a closed chamber. It can deliver excellent aeration, but blocked nozzles or pump failure give roots very little buffer time.

Common mistake: Aeroponics is a poor first system for anyone wanting a low-maintenance holiday-proof garden.

Read the full guide →

Vertical hydroponic towers: when stacking plants makes sense

A tower saves floor area but not light, access or maintenance. It works best for compact leaves and herbs when every planting pocket receives usable light.

Common mistake: Counting planting holes is not the same as counting productive plant positions.

Read the full guide →

Drip hydroponics: designing a dependable home system

Drip systems deliver measured solution to each pot through small emitters. They scale well from herbs to tomatoes, provided distribution and drainage are checked.

Common mistake: A running pump does not prove that every plant is receiving solution.

Read the full guide →

Hydroponic crops

Hydroponic lettuce: crisp leaves from a small system

Lettuce is the best first hydroponic crop: compact, quick to show problems and well suited to Kratky, DWC and NFT. Choose loose-leaf types for repeated small harvests.

Common mistake: Hot, stagnant rooms encourage weak growth and poor leaf quality.

Read the full guide →

Hydroponic basil: bushy plants and regular harvests

Basil grows readily in water culture when it has warmth, strong light and regular pruning. Pinching above a node turns one tall stem into a bushier plant.

Common mistake: Picking individual large leaves while leaving a bare stem gives poorer regrowth than cutting above nodes.

Read the full guide →

Hydroponic herbs: which ones earn their space?

Basil, mint, parsley, coriander, chives and dill are practical indoors, but they do not all want the same temperature or grow at the same speed. Group crops by habit rather than by the word “herb”.

Common mistake: A mixed countertop pod garden often becomes dominated by its fastest basil or mint plant.

Read the full guide →

Hydroponic mint: contain the roots and keep cutting

Mint is vigorous, forgiving and useful in a dedicated DWC or drip pot. Its dense roots can obstruct shared channels, so give it space and prune both shoots and roots carefully.

Common mistake: Mint’s vigour makes it a poor neighbour in a narrow NFT channel.

Read the full guide →

Hydroponic coriander: sowing for a steady supply

Coriander is best treated as a succession crop rather than a permanent plant. Sow small batches regularly and favour cooler conditions to delay flowering.

Common mistake: Repeatedly trimming a flowering plant will not restore tender leaf production.

Read the full guide →

Hydroponic parsley: slow start, long harvest

Parsley germinates slowly but becomes a dependable cut-and-come-again crop. A deeper pot and patience at the seedling stage are more valuable than strong feed.

Common mistake: Do not discard a moist parsley plug simply because faster herbs have already emerged.

Read the full guide →

Hydroponic chives: compact clumps for the kitchen

Chives suit compact systems and can be cut repeatedly. Grow a modest clump per site, keep the crown out of the solution and divide it when it becomes congested.

Common mistake: A huge clump in a tiny pod traps damp debris and becomes difficult to clean.

Read the full guide →

Hydroponic dill: tall herbs in a compact setup

Dill grows well hydroponically but quickly becomes tall and top-heavy. Give it a separate position, bright light and support, then sow replacements for tender foliage.

Common mistake: Do not place dill beneath a fixed low light shared with compact lettuce.

Read the full guide →

Hydroponic spinach: cool conditions and clean roots

Spinach can work in DWC or NFT, but it is less forgiving of warm conditions than lettuce. Fresh seed, cooler germination and good root oxygen improve the odds.

Common mistake: Warm, weakly lit growth becomes soft and prone to decline.

Read the full guide →

Hydroponic pak choi: fast Asian greens at home

Pak choi is a productive leafy crop for DWC and NFT. Baby varieties fit indoor systems better and can be harvested before thick roots and broad leaves crowd neighbours.

Common mistake: Full-size varieties can overwhelm a countertop garden designed for herbs.

Read the full guide →

Hydroponic kale: baby leaves or compact mature plants

Kale is easiest as baby leaf. Mature plants need wider spacing, stronger light and root room, so decide which harvest style you want before choosing a system.

Common mistake: Several mature kale plants cannot share the spacing intended for salad leaves.

Read the full guide →

Hydroponic watercress: clean flowing water without soil

Watercress likes constantly moist roots and can suit a shallow-flow or well-aerated system. Start from seed or a food-safe healthy cutting and keep harvested material clean.

Common mistake: Do not propagate supermarket stems that are slimy or deteriorating.

Read the full guide →

Hydroponic tomatoes: what a home setup really needs

Tomatoes need far more root volume, light and support than herbs. A drip-fed bucket or large DWC container can work, but the structure, reservoir and pollination routine must be planned first.

Common mistake: A tomato seedling may fit a countertop pod, but the adult plant and its crop will not.

Read the full guide →

Hydroponic chillies and peppers: light, warmth and patience

Chillies and sweet peppers can crop well in DWC or drip systems when they have strong light and stable warmth. They are a longer commitment than herbs and need physical support.

Common mistake: Do not start many plants unless the light footprint can cover their mature canopies.

Read the full guide →

Hydroponic cucumbers: vines, water demand and pollination

Compact greenhouse cucumbers suit drip buckets, but vines need strong support and large amounts of light and water. Choose a cultivar whose pollination requirements match the growing space.

Common mistake: Mixing unknown cucumber types indoors can create avoidable pollination and bitter-fruit problems.

Read the full guide →

Hydroponic strawberries: crowns, runners and fruit indoors

Strawberries can grow in drip or ebb-and-flow systems, but the crown must stay dry and flowers need pollination. They are attractive rather than effortless indoor crops.

Common mistake: Burying the crown encourages rot, while leaving roots exposed lets them dry.

Read the full guide →

Hydroponic beans: compact varieties and firm supports

Dwarf beans are more manageable than climbing beans indoors. Both need bright light, root space and a support that does not depend on a lightweight reservoir lid.

Common mistake: A climbing variety can outgrow a domestic light and ceiling height before it flowers well.

Read the full guide →

Hydroponic peas and pea shoots: two very different crops

Pea shoots are quick, compact and simple; podding peas require cool conditions, trellis space and more time. For indoor value, shoots usually win.

Common mistake: Do not crowd podding peas at microgreen density.

Read the full guide →

Hydroponic courgettes: possible, but rarely space-efficient

A courgette can grow in a large drip or DWC system, but its broad canopy, water use and pollination work make it a poor indoor crop for most homes.

Common mistake: Multiple courgettes under a small grow light create leaves, shade and little useful fruit.

Read the full guide →

Hydroponic microgreens: trays, hygiene and harvest

Microgreens use shallow mats or a thin medium rather than a long-term nutrient reservoir. Clean seed, clean trays, airflow and prompt harvest matter more than a complex system.

Common mistake: Persistently wet stems and crowded seed encourage mould.

Read the full guide →

Nutrients and water

Hydroponic nutrients in the UK: choosing and mixing feed

Use a complete feed labelled for hydroponics and your water type or crop stage. Follow its label by volume, add parts separately to the reservoir and measure the result instead of copying an internet recipe.

Common mistake: Never combine concentrates in a measuring cup; insoluble compounds can form.

Read the full guide →

pH and EC for hydroponics: useful measurements, simply explained

pH affects nutrient availability; EC estimates the total concentration of dissolved ions. EC cannot tell you which nutrient is missing, so use both measurements as trends alongside plant and root observations.

Common mistake: Chasing every tiny pH movement can create more instability than allowing a sensible range.

Read the full guide →

How to mix hydroponic nutrients without guesswork

Fill with water first, measure each concentrate accurately, mix between additions and make pH adjustments last. The product label—not a generic chart—sets the starting dose.

Common mistake: Adding acid or alkali to concentrated feed can cause heat, splashing and unwanted reactions.

Read the full guide →

Hard water and hydroponics in the UK

Hard water can push pH upwards and contributes minerals before feed is added. A hard-water nutrient formula and consistent measurement solve many domestic cases; treatment is not automatically necessary.

Common mistake: Buying reverse-osmosis equipment before measuring the actual problem adds cost and waste water.

Read the full guide →

Using rainwater for hydroponics: collection and caution

Rainwater is low in dissolved minerals but its quality depends on the roof, gutters, storage and local contamination. Filter it, inspect it and avoid treating “natural” as a guarantee of cleanliness.

Common mistake: Do not use stagnant water containing odour, visible contamination or animal waste.

Read the full guide →

Reservoir changes and top-ups: a sensible routine

Top up water between planned solution changes, but reset the reservoir periodically because plants do not take every ion in equal proportions. Let readings, crop stage and cleanliness guide the interval.

Common mistake: Repeatedly adding full-strength feed to replace evaporated water can drive concentration too high.

Read the full guide →

Hydroponic water temperature: keeping roots comfortable

Warm nutrient solution holds less oxygen and can favour root problems; very cold solution slows plants. Prevent direct sun on reservoirs and manage room heat before buying a chiller.

Common mistake: Frozen bottles can cause sharp local temperature swings and introduce contamination if not clean.

Read the full guide →

Lights and power

Grow lights for hydroponics: choosing coverage before wattage

Choose a light by usable coverage at the plant canopy, not by a model name or exaggerated equivalent wattage. Leafy crops need less intensity and height than fruiting tomatoes.

Common mistake: A light can appear dazzling to you while delivering poor coverage to the leaves.

Read the full guide →

Grow light running costs: calculate the real UK cost

Multiply the light’s measured watts by hours used and your electricity unit rate. Standing charges are not added because you pay them whether or not the light is on.

Common mistake: Do not use a fixture’s “equivalent watts” in the calculation.

Read the full guide →

Grow light distance: setting height by plant response

Start with the manufacturer’s hanging guidance for the crop and footprint, then watch the whole canopy. Stretching suggests too little usable light; bleaching, curling or heat stress can mean too much or too close.

Common mistake: Copying another grower’s distance is unreliable when the fixture and dimmer setting differ.

Read the full guide →

Hydroponic light schedules: timers, darkness and seasons

Use a timer to give plants a consistent daily light period and a dark period. The right duration depends on crop and intensity, so more hours cannot always compensate for a weak light.

Common mistake: Running a light continuously wastes energy and can stress plants.

Read the full guide →

Hydroponics electricity use: pumps, lights and realistic totals

The grow light usually dominates a small indoor system’s electricity use; pumps are smaller but may run continuously. Add each device’s watts multiplied by operating hours to get the total.

Common mistake: Do not compare systems on purchase price while ignoring years of light use.

Read the full guide →

Hydroponics during a power cut: protecting roots

Short light interruptions are usually less urgent than loss of root-zone aeration or circulation. In DWC, agitate the solution by hand; in NFT or aeroponics, keep roots damp while power is off.

Common mistake: Never improvise unsafe mains wiring near a wet system.

Read the full guide →

Hydroponic equipment

How to clean a hydroponic system between crops

Remove roots and debris, wash surfaces, use a suitable disinfecting method, rinse as its label requires and dry parts before rebuilding. Cleaning first matters because dirt shields microbes from disinfectants.

Common mistake: Pouring disinfectant into a dirty running system is not a substitute for physical cleaning.

Read the full guide →

Hydroponic reservoir size: stability, lifting and access

A larger reservoir changes temperature and concentration more slowly, but it is heavier to move and costlier to replace. Size it for crop demand while preserving safe access to drain and clean it.

Common mistake: A huge hidden tank is not helpful when you cannot inspect or clean it.

Read the full guide →

Air pumps and air stones for hydroponics

An air pump should deliver visible, distributed movement throughout a DWC reservoir without becoming the loudest object in the room. Position it safely and make routine checks easy.

Common mistake: Rated flow on an empty bench may not match delivery through long lines and deep water.

Read the full guide →

Water pumps for hydroponics: flow, lift and access

Select a pump by the required flow at the actual vertical lift, not its zero-head headline. Include an accessible filter and a valve or bypass for adjustment.

Common mistake: Oversizing without a safe bypass can create noisy, excessive flow.

Read the full guide →

Net pots and hydroponic growing media

The net pot supports the plant; the medium holds moisture and air around young roots. Choose a stable, clean medium that suits how often the system wets it.

Common mistake: Packing fine media tightly removes the air space roots need.

Read the full guide →

Choosing and caring for a hydroponic pH meter

A modest meter that can be calibrated and whose probe is stored correctly is more useful than an expensive neglected one. Budget for buffer and storage solution.

Common mistake: Do not store a pH probe in distilled water unless its instructions explicitly permit it.

Read the full guide →

Choosing and using an EC meter for hydroponics

An EC meter shows total ionic conductivity, making it useful for consistent mixing and trend tracking. Choose one with the measurement scale and calibration method you understand.

Common mistake: An EC reading cannot identify which individual nutrient is high or low.

Read the full guide →

Timers and controls for hydroponic pumps and lights

Use a properly rated timer with a clear manual override and verify how it behaves after a power cut. Mechanical timers are simple; digital models offer finer schedules.

Common mistake: Never put a safety-critical aeration pump on a timer by accident.

Read the full guide →

Making a hydroponic system quieter

Most noise comes from pump vibration, falling return water or air bubbles. Isolate vibration, soften the return and avoid starving pumps of water before buying replacements.

Common mistake: Wrapping an electrical pump in soft insulation can trap heat and is unsafe.

Read the full guide →

Troubleshooting hydroponics

Hydroponic root rot: signs, causes and a recovery plan

Brown colour alone is not a diagnosis because some nutrients stain roots. Concern rises when roots are slimy, fragile or foul-smelling and the plant wilts despite wet roots.

Common mistake: Adding several remedies at once hides the cause and can further stress roots.

Read the full guide →

Algae in hydroponics: block light before adding products

Algae needs light, water and nutrients. The durable fix is to exclude light from the reservoir, channels, plugs and unused planting holes, then clean away existing growth.

Common mistake: Simply dosing an algaecide without stopping light treats the symptom, not the cause.

Read the full guide →

Yellow leaves in hydroponics: diagnose by pattern

Start with which leaves yellow first, whether veins stay green and whether roots are healthy. Then check pH, EC, light and temperature before assuming the bottle lacks one nutrient.

Common mistake: Adding extra fertiliser to a locked-out or damaged root system can worsen stress.

Read the full guide →

Leaf tip burn in hydroponics: why fast growth can fail

Tip burn often appears when rapidly expanding leaves do not receive enough calcium at their edges, even when calcium is present in solution. Airflow, humidity, root health and growth rate all matter.

Common mistake: Blindly adding calcium may raise EC without fixing movement within the plant.

Read the full guide →

Hydroponic nutrient burn: recognising excess concentration

High EC, scorched margins and slowed water uptake can indicate an overly concentrated solution. Confirm with a calibrated meter, dilute or replace the reservoir, and reassess the label dose.

Common mistake: Flushing repeatedly without correcting the mixing routine guarantees a repeat.

Read the full guide →

Why hydroponic pH keeps rising

Rising pH can come from alkaline source water, plant uptake, fresh media or a small reservoir. Measure source-water alkalinity where possible and correct the underlying setup rather than adding acid every few hours.

Common mistake: Large acid corrections in a small tank can overshoot and injure roots.

Read the full guide →

Why hydroponic pH keeps dropping

A persistent pH fall can accompany biological activity, root decline, nutrient imbalance or an overly strong correction. Inspect and smell roots before treating it as a meter-only problem.

Common mistake: Repeatedly adding alkali can disguise a deteriorating root zone.

Read the full guide →

Hydroponic plants wilting despite water

Wet roots can still wilt when they lack oxygen, are too hot, have high salt exposure or cannot take up water because of disease. Start below the surface, not with another top-up.

Common mistake: A full reservoir does not prove that roots can use the water.

Read the full guide →

Hydroponic seedlings stretching: light and timing fixes

Long, thin seedlings usually need stronger or closer usable light and prompt exposure after germination. Crowding and excess warmth can add to the stretch.

Common mistake: Strong nutrient does not make weak, shaded stems sturdier.

Read the full guide →

Fungus gnats in hydroponics: remove the breeding layer

Fungus gnats breed in persistently wet organic material, including damp plugs and debris. Let exposed surfaces dry appropriately, remove decaying matter and use traps to monitor adults.

Common mistake: Spraying the room without changing wet breeding material gives only temporary relief.

Read the full guide →

Mould on hydroponic plugs: airflow, moisture and hygiene

White growth on a plug may be harmless fungal growth or a sign the surface stays too wet. Increase gentle airflow, remove dead seed tissue and keep the plug moist rather than saturated.

Common mistake: Pouring treatment onto a saturated plug can damage the seedling and leave the cause unchanged.

Read the full guide →

Clogged hydroponic lines and uneven flow

Roots, mineral deposits, media fragments and biofilm can all restrict flow. Isolate the system, find the first weak point and clean it mechanically before changing the pump.

Common mistake: Increasing pump pressure against a blockage can pop fittings or flood the area.

Read the full guide →

Indoor hydroponic pests: prevention and first response

Hydroponics prevents soil-borne weeds, not aphids, mites, thrips or whitefly. Inspect new plants, check leaf undersides and isolate a problem before choosing a food-crop-safe control.

Common mistake: Do not use an ornamental-only pesticide on crops you plan to eat.

Read the full guide →

Planning and seasons

Hydroponics in a flat: food from a small space

For a flat, favour quiet, covered systems with a footprint you can lift when partly drained. Herbs and cut-and-come-again leaves give more value than one sprawling fruiting plant.

Common mistake: Vertical towers look space-efficient but need headroom, pump access and protection from drips.

Read the full guide →

UK hydroponics calendar: what changes through the year

Indoor hydroponics can run all year, but natural light, room heat and ventilation change with the seasons. Use winter for lit leaves and spring to raise greenhouse transplants; watch reservoir heat in summer.

Common mistake: A fixed annual schedule ignores the actual temperature and light in your growing spot.

Read the full guide →

Winter hydroponics in the UK: light before heat

For most homes, winter success depends first on adequate light and then on avoiding cold roots and condensation. Leafy crops and herbs are more realistic than fruiting vines.

Common mistake: Heating a dark space for tomatoes is expensive and rarely sensible for a beginner.

Read the full guide →

Greenhouse hydroponics in the UK: seasons and safeguards

A greenhouse supplies free seasonal light but brings temperature swings, frost risk and greater summer water demand. Drip buckets suit fruiting crops; passive leaves suit shoulder seasons.

Common mistake: A greenhouse does not remove the need to manage heat; it magnifies it on sunny days.

Read the full guide →

Leaving hydroponics while on holiday

A proven, simple system with a full reservoir can be left more safely than a newly changed one. Arrange a knowledgeable checker for longer absences and leave written limits rather than asking them to improvise.

Common mistake: Do not rebuild or transplant the day before travel.

Read the full guide →

Planning a continuous hydroponic harvest

Continuous harvest comes from staggered sowing, not from keeping old plants forever. Divide the system into seedling, growing and harvest stages and record how long each crop takes in your conditions.

Common mistake: Filling every site on day one creates a glut followed by an empty system.

Read the full guide →

What not to grow hydroponically at home

Large root crops, sprawling field crops and plants whose edible yield is tiny relative to their canopy are usually poor domestic hydroponic choices. Possible does not mean worthwhile.

Common mistake: Viral examples often prove possibility while hiding the space, energy and labour used.

Read the full guide →

Starting hydroponics on a budget

Spend first on safe containment, a suitable light and complete nutrient. A reused opaque food-safe container can perform as well as a styled reservoir; poor meters and unnecessary gadgets can wait.

Common mistake: Buying a large cheap kit can cost more after replacing weak lights, leaky fittings and inaccurate accessories.

Read the full guide →

Hydroponic comparisons

Hydroponics vs soil: which suits a UK home?

Hydroponics is useful where clean indoor growing, compact spacing and predictable watering matter. Soil is cheaper, more buffered and usually simpler outdoors. Neither method is automatically better.

Common mistake: Claims that hydroponics always uses less water ignore reservoir changes, cleaning and the comparison baseline.

Read the full guide →

Aquaponics vs hydroponics for home food growing

Hydroponics feeds plants with measured mineral nutrients. Aquaponics couples plants to a living fish and microbial system, so it is harder to balance and carries animal-welfare duties.

Common mistake: Do not buy fish as components for an uncycled plant system.

Read the full guide →

Best hydroponic system for beginners: compared on effort and risk

For one lettuce or basil plant, Kratky is the simplest. For a reusable powered setup, a small DWC system teaches more and handles top-ups well. NFT and aeroponics add failure points beginners do not need.

Common mistake: There is no universal best system independent of crop, space and maintenance.

Read the full guide →

Best indoor herb gardens in the UK: compared on useful criteria

The best format depends on whether you value convenience or replaceable standard parts. Compare usable plant spacing, light coverage, reservoir access, consumable lock-in and published power draw—not the number of pod holes.

Common mistake: We have not tested these products; this framework compares published information and ownership practicalities.

Read the full guide →

Are smart gardens worth it? A candid UK cost check

A smart garden is worth considering if automation removes the barrier that stops you growing herbs. It is poor value if you enjoy DIY, expect supermarket-cost produce or dislike buying replacement pods.

Common mistake: Do not justify a premium appliance with unrealistic harvest or payback claims.

Read the full guide →

Click & Grow vs AeroGarden: choose by UK support and consumables

Compare current UK availability, warranty support, pod flexibility, light power and mature plant spacing before choosing. A product that is hard to support locally is a poor buy even when its headline specification looks stronger.

Common mistake: We have not tested these products; confirm every current specification with the maker before buying.

Read the full guide →

DIY vs ready-made hydroponics: cost, control and time

DIY systems give replaceable parts and exact sizing; ready-made systems reduce design work and can look neater. The cheaper choice depends on whether you already own tools and value troubleshooting time.

Common mistake: A DIY total that omits the light, meters and spare fittings is not a fair comparison.

Read the full guide →